Screw valve series

Home > Product > Screw valve series

TD-V1L-21016
Description :

Plastic parts use rotating locking structure, which is more safe and reliable than straight plug

The mechanism seal adopts lateral extrusion seal to solve the problem of end surface deformation

The gear adopts external tooth drive and high-performance motor to avoid the problem of internal tooth jamming, and the continuous operation times can reach 60,000 times

Full-card buckle design without a single screw

The conical sleeve piston dynamic seal is used to completely solve the problem of old bellows

Nut and wire rod use radial anti-lock structure, high voltage open, low voltage off more reliable

The valve seal bracket adopts guided positioning, and the on and off valve is more smooth, without shaking

Share to :

Performance

Plastic parts use rotating locking structure, which is more safe and reliable than straight plug

The mechanism seal adopts lateral extrusion seal to solve the problem of end surface deformation

The gear adopts external tooth drive and high-performance motor to avoid the problem of internal tooth jamming, and the continuous operation times can reach 60,000 times

Full-card buckle design without a single screw

The conical sleeve piston dynamic seal is used to completely solve the problem of old bellows

Nut and wire rod use radial anti-lock structure, high voltage open, low voltage off more reliable

The valve seal bracket adopts guided positioning, and the on and off valve is more smooth, without shaking

Technical

service substance

Natural gas, liquefied petroleum gas

Flow range

(0~6)m³/h

working pressure range

(0~15)KPa

working temperature

-20℃~+55℃

storage temperature

-25℃~60℃

relative humidity

≤93%RH

pressure loss

50Pa, flow rate of 6m³ / h (valve tested separately)

Sealability (inside)

P = 5 kPa, leakage of <0.55 L/h

durability

No fault after 10,000 consecutive operation

voltage

DC2.5~5.5V

Crossing the voltage: DC1.5V

working current

≤80mA

peak point current

≤200mA

Work resistance

27Ω ±10%(20℃)

Work inductance

20.3mH±15%(20℃)

Valve opening / close time

≤1.5s

explosion-proof criteria

In accordance with GB / T3836.1, GB / T3836.4, IEC60079-0, IEC60079-11, IS080079-36, IS080079-37, andExib llB T4GB

Structural support

Material is polyformaldehyde, the valve sealing material is nitrile rubber

Adaptation of the phenotype

G2.5 and G4 gas meters


Dimensions

Online Inquiry

Our most valued customer, if you have any questions, you can leave a message below or call 021-59869333,
We will get in touch with you as soon as possible and serve you wholeheartedly. (* is required, sincerely thank you for your message.)
  • Name *
  • Phone *
  • E-mail *
  • Address
  • Content
You might be interested
TD-V1L-21035
Plastic parts use rotating locking structure which is more safe and reliable than straight plug The mechanism seal adopts lateral extrusion seal to solve the problem of end surface deformation The gear adopts external tooth drive and high-pe...
TD-V1L-22003(G25)
The plastic parts are connected by rotating locking structure which is safer and more reliable than the straight plug type The mechanism seal adpots the side extrusion seal solves the end face deformation problem The gear is driven by extern...
TD-V1L-22002(G10)
The plastic parts are connected by rotating locking structure which is safer and more reliable than the straight plug type The mechanism seal adopts the side extrusion seal solves the end face deformation problem The gear is driven by extern...
TD-V1L-22001(G6)
The plastic parts are connected by rotating locking structure which is safer and more reliable than the straight plug type The mechanism seal adopts the side extrusion seal solves the end face deformation problem The gear is driven by extern...
TD-V1L-21007
The plastic parts are connected by rotating locking structure which is safer and more reliable than the straight plug type The mechanism seal adopts the side extrusion seal solves the end face deformation problem The gear is driven by extern...
TD-V1L-21005
The plastic parts are connected by rotating locking structure which is safer and more reliable than the straight plug type The mechanism seal adopts the side extrusion seal solves the end face deformation problem The gear is driven by extern...
TD-V1L-21003
The plastic parts are connected by rotating locking structure which is safer and more reliable than the straight plug type The mechanism seal adopts the side extrusion seal solves the end face deformation problem The gear is driven by extern...
TD-V1L-21001
The plastic parts are connected by rotating locking structure which is safer and more reliable than the straight plug type The mechanism seal adopts the side extrusion seal solves the end face deformation problem The gear is driven by extern...
  • Technical certification
  • Testing equipment
  • 0572-5851118
    18381014295
  • Working hours Monday to Friday 8:30-17:30

  • 13059979398
  • 24-hour online consultation
Copyright © Anhui Tiandun Electronics Co., Ltd. all rights reserved Support:Shanghai website
Building 1, Science and Technology Pioneer Park, Anji County, Zhejiang Province